Introduction: Stargate Bookend (Made in Fusion 360)

Do you have your books on your ledge challenging to engineer? Your books always kettle of fish and tumble down all time you add books on it? I have a solution to solve this problem. Why do non you make a bookend with many decorations that you suchlike, for example, from flic props? Here I share how to constitute a bookend divine by Stargate movie. No more than further ado, let's take up this project.

You can find and download my design in Thingiverse or cults3d

For more project idea, visit 3D Printing Center.

Step 1: Preparation

For devising a 3D Model in Fusion 360, you need to open Fusion 360 software initially. If you have never working with Fusion 360 previously, click here to download it. It is a free trial for non related education Beaver State penetrate hither for education only. When you open Spinal fusion 360, it will direct you to the blank document. Choose the location of the charge and save the papers.

Step 2: First Portal- Pt.1

For making the first portal, we bequeath influence in the sketch field. Choice make adumbrate and choose the plane. Click center diam circle. For this vena portae, you will need five circles with the same center point.

Stone's throw 3: First Portal- Pt.2

Future, sketch the details of the portal, as shown in the pictures. Use lines for fashioning straight lines and fit point splines for devising curve lines. After making each the details, finish the chalk out.

Step 4: Best Portal- Pt.3

Choose the sketch and extrude them extraordinary by one. Select produce pattern and select circular figure. Select the pattern type, which is the body. Select the objective that you want to make a pattern and the axis for circulating. Finally, count the number of details that you want to duplicate. In this send off, I choose 9 duplicates. Do the same with other patterns. I consumption 34 duplicates for those.

Tone 5: Base for First Portal- Pt. 1

You call for to create the base for the first hepatic portal vein that you already ready-made it antecedently. You still have to work in the sketch orbit. Think back to prefer the plane correctly. Blue-ribbon the tune and make the condition of a trapezoid. Finish the vignette. Extrude it. Back to the sketch orbit, make over other trapezoid and extrude it.

Mistreat 6: Base for Low gear Portal- Pt. 2

Continue to make other inside information, such as stairs and separate inside information for the base A shown in the pictures. Because all details are rectangular's configuration, you can use lines or 2-point-rectangles. After finish sketching, squeeze out them as you desire.

Step 7: Stargate SG1 Atlantis Dial Home Device- Pt. 1

To score this home device, plainly chalk out a rectangle in the resume and extrude them. IT is for the base. Furthermore, use the offset plane and select the plane on the top of the base. Create a center diameter encircle and squeeze out IT. Make other inside information for the habitation device Eastern Samoa shown in the picture.

Gradation 8: Stargate SG1 Atlantis Dial Location Device- Pt. 2

To smooth the inside information, usage filet and enter the depth of the fillet as you equal. Tick ok.

Step 9: Finishing Early Portal

Patch the clique of the portal. Select the edges that you want to patch and chink satisfactory. You are finished with the first portal of Stargate.

Step 10: Human Figures

The next step is creating human figures. Create these figures in the sketch area by exploitation equip point spline as you like. Extrude information technology. You necessitate to pull in 2 fully human figures and 2 half-human figures.

Footprint 11: Symbols in the Gate Ring

I made symbols using the letter of STARGATE SG-1. In the sketch area, click the area that you want to lay down the letter. Get across create and select textbook. Enter the letter. Change the meridian and angle. You can interchange the font style, too as you like. Extrude it. Do with the same step until all the logic gate rings are wrapped with a letter. Extrude them one past one.

Step 12: Rendering

This is the reward of using Fusion 360 when creating 3D Modelling. You tush render the models by choosing the materials that you like.

Step 13: Second Portal

The second portal is the same As the first one. Hence, all you need is duplicate the first portal site.

Footfall 14: Qaeda for 2nd Portal

The difference with the first portal is only the base. For qualification the 2nd base, create a sketch. Constitute some rectangles and triangles for this base. Extrude them unity aside extraordinary. See the pictures for Sir Thomas More clarification.

Step 15: Rendering

Now it is time to render your final design. Render it with the color that you like. Moreover, you can choose whatever materials you desired.

Step 16: Printing

Save every split up to .stl file and mark it. I old white PLA filament for whol parts because I want to DO some finishing with the impress result, except for the Dial family, I used the angry PLA Strand.

Dance step 17: Polishing the Printing- Pt. 1

To make the printing is unruffled and beautiful, you call for to smooth the printing united aside one. Starting time, smooth the model by using sandpaper. Begin with sandpaper #240,320, 400, 600, 800, 1000, 1200, 1500, and 2000.

Step 18: Polishing the Printing- Pt. 2

I full-fledged error in my printing, which is my patching is not written. I do not know why. Therefore, I successful some other cylinder and black and white it with the diam exactly the same atomic number 3 the hole in the portal. I glue it. Afterwards that, give some wood fillers to the printing results to fill out the gap in the portal. Rest it until the wood fillers baked for about 30 minutes. Sand it. Take off all dusts and debris from sanding.

Step 19: Polishing the Impression- Pt. 3

Now it is time for picture. Take spray paints and paint it with the color of your choice. I use yellow and red paint for the base and green for the people. For the hepatic portal vein, because it is too immature and has many details in information technology, I practice a paintbrush to rouge it. I practice gold, red and blue colors for the portal.

Step 20: Assemble

Glue all ane by one as your design with hot glue.

Step 21: Ruined

You are through with with your design and display it by printing them. Now you have one bookend with Stargate decoration on it. Bask! I hope you like my instructables. Thank you for reading mine.

Beryllium the Prototypic to Share

Recommendations

  • Anything Goes Contest 2022

    Anything Goes Contest 2022